😎 100% Tint Window Tinting

😎 100% Tint Window Tinting has a stated focus on Ceramic tint, UV protection, Heat rejection, Premium film brand, and Lifetime warranty as part of its window tinting and automotive film work. The relevant scope can depend on the requested service, location, timing, and the information supplied before an appointment or estimate. The street address shown for the business is 8725 Youngerman Ct Suite 102, Jacksonville, FL 32244, United States. Direct contact is available by phone and through the company website. Review recent terms and contact information directly when timing, travel, documents, property access, or payment details matter. Before arranging service, ask which film brands are used, how legal limits are handled, what warranty applies, and how curing or aftercare is explained. For project work, request a written scope that identifies materials, labor, timing, exclusions, and warranty terms. Clear written answers make it easier to compare the offering with the specific need.

Address

8725 Youngerman Ct Suite 102, Jacksonville, FL 32244, United States

Phone

+1 904-844-8468

Website

windowtintjacksonville.com/

Source depth

100 of 100

Indexable

Standalone profile

FL sits in the Permissive (sun-belt) band. Florida allows 28 % front and 15 % rear — among the most permissive in the country. Reflectivity caps still apply at 25 %.

Across all fifty states, the only zone of the windshield where any non-reflective tint is legal is the strip above the AS-1 line — usually four to five inches at the top, marked on factory glass with a small "AS-1" etching. Below that line, windshield tint is not street-legal anywhere in the United States, regardless of state side-glass rules. A reputable shop will measure from the AS-1 line down before laying film, not from the top of the glass.

Laws change. Confirm the most recent VLT minimum directly with the shop and, when in doubt, with the most recent text of your state's vehicle code.

1. Ask for the IRR and TSER numbers on the spec sheet.Heat rejection at a given VLT comes from infrared rejection (IRR) and total solar energy rejected (TSER). The shop's top ceramic line will publish both numbers. A dyed film and a top ceramic at the same VLT can differ by 30 percentage points on TSER.
2. Read the lifetime warranty before signing.Most "lifetime" wording in tint covers fade, bubbling, peeling, and cracking — not stone chips, edge lift from worn window seals, or ammonia-cleaning damage. Some are original-owner-only; others transfer with a small fee. The transferable clause is what protects resale.
3. Confirm the shop measures front-window VLT before install.A shop that measures with a photometer before installation is the one most likely to keep you legal in your state. If they ask you to sign that compliance is on the customer, that's a quiet yellow flag. Tint stops are 28 % on the front in FL.
4. Ask the cure time and what to do during it.Newly installed film cures for 3 to 5 days in summer, 7 to 10 in winter. During cure, do not roll windows down — the film can shift and the squeegee margins can lift. Light hazing or small water bubbles in this window are normal and clear up; bubbles after 30 days are not.
5. Verify the AS-1 line on your windshield before booking strip tint.Across all 50 states, the only zone of the windshield where any tint is legal is above the AS-1 line — usually marked with a small "AS-1" etching at the top of factory glass. Below the AS-1 line, no tint is street-legal anywhere in the U.S., regardless of your state's VLT rule on side glass.
6. Pull a window seal vs. cut on glass — ask what the shop does.Cut-on-glass installs save 15 minutes but risk scoring the rubber seal with a razor. The cleaner method pulls the rear-side or rear-glass window down a half-inch so the cut happens off-glass. It costs the shop time, not money — confirm during the quote.